- Posts: 3
- Thank you received: 0
Remove Isogen Dimensions for Couplings and Unions
- DragonServ
- Topic Author
- Offline
- New Member
Less More
9 years 8 months ago - 9 years 8 months ago #8552 by DragonServ
Remove Isogen Dimensions for Couplings and Unions was created by DragonServ
Hello all
I am fairly new to setting up isogen, and have been using Pipman 2010 to set it up. We are getting these Dims on the unions and couplings and a few tees that print out much lighter then the Dims that come in on a Iso plane. Is there a way to turn just these Dims off?
Attached is a copy of one of the iso's. When opened take a look at the "54" on the bottom right corner compared to the "156" that's on the DIM line near it.
Thanks
I am fairly new to setting up isogen, and have been using Pipman 2010 to set it up. We are getting these Dims on the unions and couplings and a few tees that print out much lighter then the Dims that come in on a Iso plane. Is there a way to turn just these Dims off?
Attached is a copy of one of the iso's. When opened take a look at the "54" on the bottom right corner compared to the "156" that's on the DIM line near it.
Thanks
Please Log in or Create an account to join the conversation.
- Jop
- Offline
- Moderator
Less More
- Posts: 1053
- Thank you received: 14
9 years 8 months ago - 9 years 8 months ago #7114 by Jop
Do it once and Do it Right
Replied by Jop on topic Re: Remove Isogen Dimensions for Couplings and Unions
This pipingdesigners.com Technical Forum is possibly not the place to get the answer you need.
I suggest you try here: www.coade.com/FAQ/163#Isogen
I suggest you try here: www.coade.com/FAQ/163#Isogen
Do it once and Do it Right
Please Log in or Create an account to join the conversation.
- DragonServ
- Topic Author
- Offline
- New Member
Less More
- Posts: 3
- Thank you received: 0
9 years 8 months ago - 9 years 8 months ago #7115 by DragonServ
Replied by DragonServ on topic Re: Remove Isogen Dimensions for Couplings and Unions
Technically, Setting up Isogen would be a Technical question , So I believe the question belongs in this forum
I am just trying out every resource I have at my disposal. Coade is no help in training without paying, and most other designers who set up isogen seem to keep their info close to their chest.
The FAQ link is a link to Isogen Issues. I need help with advanced setup.
This was the last places I had to try.
I am just trying out every resource I have at my disposal. Coade is no help in training without paying, and most other designers who set up isogen seem to keep their info close to their chest.
The FAQ link is a link to Isogen Issues. I need help with advanced setup.
This was the last places I had to try.
Please Log in or Create an account to join the conversation.
- Anton
- Offline
- Administrator
9 years 8 months ago - 9 years 8 months ago #3667 by Anton
- If you're the smartest person in the room ... you're in the wrong room.
Replied by Anton on topic Re: Remove Isogen Dimensions for Couplings and Unions
Have you tried asking the guys at www.davetyner.com on the forum there?
They are fantastic with the software end of things ... I'm pretty sure they will have an answer, tell them you were refered from here and I'm sure they will prioritize you!
p.s. ... I'm going to move this to the software forum.
They are fantastic with the software end of things ... I'm pretty sure they will have an answer, tell them you were refered from here and I'm sure they will prioritize you!
p.s. ... I'm going to move this to the software forum.
- If you're the smartest person in the room ... you're in the wrong room.
Please Log in or Create an account to join the conversation.
Time to create page: 0.239 seconds